Car Engine Flywheel

At the power output end of the crankshaft, that is, even the gearbox and the side connected to the work equipment. The main role of the flywheel is to store the energy and inertia of the engine outside the work stroke. The four-stroke engine only work a stroke of suction, compression, exhaust energy from the flywheel storage energy.
Flywheel has a large rotational inertia. As the engine work of each cylinder is not continuous, so the engine speed is also changing. When the engine speed increases, the kinetic energy of the flywheel increases, the energy stored; when the engine speed decreases, the flywheel kinetic energy decreases, the energy is released. The flywheel can be used to reduce the speed fluctuation of the engine running process.
Installed in the rear end of the engine crankshaft, with rotational inertia, its role is to store the engine energy, to overcome the resistance of other components, so that the crankshaft evenly rotate; through the clutch mounted on the flywheel, the engine and car transmission connected; and the starter engaged, easy to start the engine. And it is the integration place of crankshaft position sensing and vehicle speed sensing.
The energy transmitted to the crankshaft by the engine during the work stroke, in addition to the external output, some energy is absorbed by the flywheel, so that the crankshaft speed does not rise much. In the exhaust, intake and compression three strokes, the flywheel will release its stored energy to compensate for the work consumed in these three strokes, so that the crankshaft speed does not decrease too much.
In addition, the flywheel has the following functions: the flywheel is the active part of the friction clutch; the flywheel rim is inlaid with the flywheel ring for starting the engine; the flywheel is also inscribed with the upper stop mark, which is used to calibrate the ignition timing or injection timing, as well as adjusting the valve clearance."
"At the power output end of the crankshaft, that is, even the gearbox and the side connected to the work equipment. The main role of the flywheel is to store the energy and inertia of the engine outside the work stroke. The four-stroke engine only work a stroke of suction, compression, exhaust energy from the flywheel storage energy.
Flywheel has a large rotational inertia. As the engine work of each cylinder is not continuous, so the engine speed is also changing. When the engine speed increases, the kinetic energy of the flywheel increases, the energy stored; when the engine speed decreases, the flywheel kinetic energy decreases, the energy is released. The flywheel can be used to reduce the speed fluctuation of the engine running process.
Installed in the rear end of the engine crankshaft, with rotational inertia, its role is to store the engine energy, to overcome the resistance of other components, so that the crankshaft evenly rotate; through the clutch mounted on the flywheel, the engine and car transmission connected; and the starter engaged, easy to start the engine. And it is the integration place of crankshaft position sensing and vehicle speed sensing.
The energy transmitted to the crankshaft by the engine during the work stroke, in addition to the external output, some energy is absorbed by the flywheel, so that the crankshaft speed does not rise much. In the exhaust, intake and compression three strokes, the flywheel will release its stored energy to compensate for the work consumed in these three strokes, so that the crankshaft speed does not decrease too much.
In addition, the flywheel has the following functions: the flywheel is the active part of the friction clutch; the flywheel rim is inlaid with the flywheel ring for starting the engine; the flywheel is also inscribed with the upper stop mark, which is used to calibrate the ignition timing or injection timing, as well as adjusting the valve clearance.

Flying wheel (flying wheel), rotating inertia of a large disk-shaped parts, its role as an energy storage. For four-stroke engines, every four piston strokes to do work once, that is, only the work stroke to do work, and exhaust, intake and compression three strokes to consume work. Therefore, the crankshaft external torque output is cyclical, the crankshaft speed is also unstable. In order to improve this situation, the flywheel is installed at the back end of the crankshaft. The rotational inertia of a large disk-shaped parts, its role as an energy storage. For four-stroke engines, every four piston strokes to do work once, that is, only the work stroke to do work, while the exhaust, intake and compression of the three strokes are to consume work. Car engine flywheel is used as a passive part of the starter motor, is the active part of the clutch, generally divided into two kinds, one is a mechanical clutch, one is a liquid joint, the latter is used for self-exhaust cars. The friction surface of the flywheel is in contact with the clutch plate of the clutch when the car is moving and the power is transmitted to the transmission. When the driver depresses the clutch pedal, the clutch plate leaves the flywheel, interrupting the power transmission and shifting gears. When the driver releases the pedal, the clutch plate touches the flywheel and power transmission resumes.

Mianyang Anzhou Great Wall Machinery Manufacturing Co., Ltd office is located in Li Bai's hometown (Mianyang), Mianyang City, Mianyang City, Anzhou District, Jiepai Town, Shi'an Village, Group 14, was registered on June 18, 2008 in Mianyang City, Anzhou District Food and Drug and Industry and Quality Supervision Administration, with a registered capital of 500,000 yuan, in the company's 14 years of development and growth, we have always provided customers with good products and technical support, sound In the 14 years of our company's development and growth, we have always provided our customers with good products and technical support, sound after-sales service, our company is mainly engaged in auto parts manufacturing, casting, sales; machining, manufacturing, sales; scrap metal acquisition, sales and storage services. We have good products and professional sales and technical team, our company belongs to the Mianyang machinery and equipment company industry, if you are interested in our products and services, look forward to your online message or call.

 

Cheng Ke

402217555@qq.com

 OUR STORE 

Disclaimer: This article is reproduced from other media. The purpose of reprinting is to convey more information. It does not mean that this website agrees with its views and is responsible for its authenticity, and does not bear any legal responsibility. All resources on this site are collected on the Internet. The purpose of sharing is for everyone's learning and reference only. If there is copyright or intellectual property infringement, please leave us a message.
©Copyright 2009-2020 Yahoo Perspective   cryydr@163.com   Contact Us   SiteMap